Open 24/7 · phones answered live Licensed, Bonded & Insured · Instant Estimate $0 down financing 501.441.2900

Search patriotroof.net

Can't find it? Call 501.441.2900, open 24/7, or book an inspection.

Book an Inspection

How Much Attic Ventilation Do I Need? Calculator and Chart

A Patriot Roofing and Restoration inspector on a ladder pointing out roof details while a team member and the homeowner watch

Most homes need 1 square foot of net free vent area for every 300 square feet of attic floor, split about evenly between intake vents low at the eaves and exhaust vents high near the ridge. If the vents are not split between high and low that way, the International Residential Code doubles it to 1 square foot for every 150 square feet. In practice, at the 1/300 rate, plan on about 0.24 square inches of intake and 0.24 square inches of exhaust for every square foot of attic floor. A 1,500 square foot attic works out to 720 square inches in all: 360 in at the soffits and 360 out at the top.

We are Patriot Roofing and Restoration in Maumelle, and we size ventilation on every roof we replace. Below is the same math we use, step by step, with a table for common attic sizes. Vent ratings come from the makers' own pages (Lomanco and Atlas, checked November 2026). Treat the numbers as a way to check your attic, not as a design for your house.

The attic ventilation formula in four steps

  1. Measure the attic floor. Use the area of the ceiling below the attic, not the roof. On a one-story home it is close to the heated living area (garage attics are often a separate space). On a two-story home with one attic, divide the living area by two. That is the same estimate our roof calculator uses.
  2. Divide by 300 (or 150). The answer is the total net free area (NFA) you need, in square feet. Lomanco describes 1/150 as the code baseline and 1/300 as the reduction allowed when the vent placement conditions are met; Atlas's ventilation instructions quote the same rule, with 40 to 50 percent of the vent area up high and the rest low at the eaves. Some local codes call for 1/150 regardless, so check with your building department.
  3. Multiply by 144. Vent ratings are printed in square inches, and there are 144 square inches in a square foot.
  4. Split it in half. Half is exhaust, half is intake. Lomanco says intake "should meet or slightly exceed" exhaust, and Atlas says soffit intake should equal ridge exhaust. If the two cannot match, it is the intake that should come out ahead.

Then divide each half by the NFA of the vent you plan to use, and round up. Lomanco's own example: a 2,000 square foot attic at 1/300 needs 6.67 square feet, or 960 square inches, so 480 square inches of exhaust and 480 of intake. With its 750 slant back roof vent at 50 square inches each, that is 9.6, rounded up to 10 vents. "Always use the manufacturer's published NFA rating," Lomanco says, because two vents that look alike can be rated very differently.

Attic ventilation chart for common attic sizes

These figures use the 1/300 rule and three published ratings: 18 square inches of NFA per foot of ridge vent (Lomanco and Atlas both list several shingle-over ridge vents at that rating), 50 square inches per static box vent (Lomanco's 750 and Atlas's AL 50 and GL 50 slant back vents), and about 11 square inches per foot of continuous soffit vent (Lomanco's Model 140 is rated 88 square inches per 8-foot piece). Every count is rounded up.

Attic floor (sq ft)Total NFA (sq in)Exhaust (sq in)Intake (sq in)Ridge vent (ft)Or box ventsContinuous soffit vent (ft)
1,20057628828816627
1,50072036036020833
1,80086443243224940
2,000960480480271044
2,5001,200600600341255

If your attic falls under the 1/150 rule, double every number in the table. Ridge vent footage is the length of vent installed, not the length of the ridge. If the ridge on your house is shorter than the footage needed (common on hip roofs), a ridge vent alone may not be enough exhaust, which is when box vents, turbines or a solar attic fan come into the conversation. Our guide to roof ventilation types covers which exhaust fits which roof.

A worked example: 1,800 square foot ranch home

  • 1,800 divided by 300 is 6 square feet of total NFA.
  • 6 times 144 is 864 square inches.
  • Half is 432 square inches of exhaust and 432 of intake.
  • Exhaust as a ridge vent rated 18 square inches per foot: 432 divided by 18 is 24 feet of vent.
  • Intake as continuous soffit vent at about 11 square inches per foot: 432 divided by 11 is 39.3, so 40 feet. With Atlas's HighPoint Intake Eave Vent, which Atlas rates at 9 square inches per foot for homes with little or no soffit, it would be 48 feet.

Round 8-inch soffit vents show why the vent type matters. Lomanco rates its round vent at 13 square inches each, so the same 432 square inches of intake would take 34 of them. A house with eight round vents under the eaves and a full ridge vent on top is a common sight, and it is short on intake by a wide margin.

Powered and solar fans follow different math

The 1/300 rule is for passive vents. A fan is rated by the air it moves, and it needs enough intake to feed it. Attic Breeze's data sheet for its 35-watt model lists a minimum intake of 1,008 square inches of NFA per fan, well above the 408 square inches the 1/300 rule gives for the intake side of a 1,700 square foot attic. Without that intake, a fan pulls air from wherever it can, including through other roof vents or from the house below. We size one Attic Breeze solar fan for up to 1,700 square feet of attic floor, and we do not install a fan beside a ridge vent; our solar attic fan vs ridge vent comparison explains why.

What changes the answer for your house

  • More than one attic. A garage attic, a bonus room or a vaulted section that is closed off from the main attic is its own space and needs its own intake and exhaust.
  • Mixed exhaust. Lomanco and Atlas both say to use one type of exhaust per attic. A ridge vent plus a row of box vents does not add up the way the table suggests; the lower vents can act as intake and short-circuit the ridge. Atlas says its system warranty covers only one type of exhaust vent per attic area.
  • Blocked intake. Soffit vents painted shut or buried under blown-in insulation count for nothing, whatever their rating. Our soffit vents guide covers what blocks them and how baffles keep the path open.
  • Vaulted and cathedral ceilings. Where the ceiling follows the roof line, the air has to move through each rafter bay, and the vents have to line up with those bays. That is a case for a closer look rather than a chart.
  • Local code. Your building department has the final word on which ratio applies.

Why it matters on a Central Arkansas roof

Our summers are long, hot and humid, so an attic with too little airflow bakes the underside of the shingles and loads the air conditioner, and in winter, warm damp air from the house can condense on a cold roof deck. Ventilation is also part of the shingle warranty conversation, because shingle makers require proper attic ventilation. Getting the numbers right is cheap compared with replacing rotted decking.

How Patriot sizes ventilation

Every Patriot roof replacement includes ventilation sized to the attic: a ridge vent with balanced intake on our Armor, Shield Plus and Shield roofs (metal-compatible on Armor), and whirlybird turbines on Economy. On a roof you are keeping, ventilation work is priced in writing after we look at the attic. Ventilation is part of every 21-point roof inspection. It is free with a storm or replacement inspection, and part of the $79.99 repair diagnostic visit (no fee for Patriot Care Club members). Our attic ventilation page shows what we check and how we fix it.

Frequently asked questions

How many square inches of ventilation do I need per square foot of attic?

At the 1/300 rule, 0.48 square inches of net free area per square foot of attic floor in all, or about 0.24 for intake and 0.24 for exhaust. At 1/150 it is double: 0.96 in all.

How many feet of ridge vent do I need?

Take your exhaust number in square inches and divide by the vent's rating per foot. With an 18 square inch per foot ridge vent at the 1/300 rule, that is roughly 1 foot of vent for every 75 square feet of attic floor. Intake has to match it.

Can you have too much attic ventilation?

Too much exhaust without matching intake is a real problem, because the exhaust starts pulling air from the wrong places. Balanced vent area above the minimum is rarely the issue; mismatched or mixed vents are.

Do I count the gable vents?

Gable vents are a separate exhaust type. Lomanco gives a ridge vent with gable vents as an example of mixing to avoid, so on a ridge-vented attic they are not counted as extra exhaust. We look at how they affect airflow before deciding whether they stay open.

How do I find a vent's net free area?

Look on the vent's label, packaging or the maker's website. The NFA is smaller than the size of the opening, because screens and louvers block part of it.

Want us to run the numbers on your attic?

We measure the attic, check the intake from outside and inside, and count what is already on the roof before recommending anything. Contact us or call 501.441.2900 to book a visit.

Inspection

21-Point Roof Inspection

Your Roofing Specialist checks the roof and attic and gives you a 21-point report with photos of what we find.

$79.99

Roof Repair Diagnostic Visit

Includes the 21-Point Roof Inspection Report and attic analysis. Patriot Care Club members pay no service fee.

Book it now

Have No Fear, Patriot Is Here!

Call any time. Our phones are answered live 24/7.

Financing available, with approved credit

$0 down, 0% financing for 12 months, or payments of about $176 a month on $15,000 at 12.99% APR for 240 months. Soft credit check, approval in as little as 60 seconds.

Check My Options

Financing is with approved credit. Promotional rates and terms are not guaranteed and can change at any time. Payment example: $15,000 financed with $0 down at 12.99% APR for 240 months is 240 monthly payments of $175.63. 0% financing for 12 months is a promotional offer from the lender; the terms that apply after the promotional period are set by the lender. We work with more than one lending partner, and the rates and terms you are offered are set by the lender you are approved with, not by Patriot Roofing and Restoration. All rates and terms are presented to you in writing before you sign anything.

Instant Estimate