Open 24/7 · phones answered live Licensed, Bonded & Insured · Instant Estimate $0 down financing 501.441.2900

Search patriotroof.net

Can't find it? Call 501.441.2900, open 24/7, or book an inspection.

Book an Inspection

Roof Truss vs Rafter: How to Tell Them Apart and Why It Matters

A Patriot roofing crew member tearing off old shingles down to the roof deck

Rafters and trusses are the two ways a roof frame gets built. Rafters are single sloped boards cut and set one at a time on site, running from the top of the wall up to a ridge board at the peak, with ceiling joists or rafter ties keeping the walls from spreading. Trusses are triangles built in a factory from smaller lumber joined with metal plates, then lifted onto the walls whole. Rafters leave open attic space and suit vaulted ceilings and custom shapes; trusses go up faster and span the house with lighter lumber, but their webs fill the attic and no part of them may be cut without an engineer's approval. For a new roof, either kind of frame can carry new shingles or metal. What matters is that the frame is straight, dry and unaltered.

Truss vs rafter at a glance

Rafters (stick framing)Trusses
How it is builtCut and nailed one board at a time on siteBuilt in a plant to a drawing, delivered ready to set
What it looks like in the atticSloped boards up to a ridge board, flat ceiling joists below, mostly open spaceA repeating pattern of triangles with diagonal and vertical web pieces
Typical lumberLarger boards, often 2x6 to 2x12Smaller boards, usually 2x4 or 2x6
JointsNails, sometimes metal hangersToothed metal connector plates pressed into the wood
Who designs itCode span tables or a designerThe truss maker's engineering software, on a truss design drawing
Attic storage and roomsGood, the space is openLimited, unless special attic trusses were ordered
Vaulted ceilingsCommonPossible with scissor trusses
Can you cut or move a piece?Only with care and proper reinforcementNo, not without approval from the truss maker or an engineer

How to tell which one your house has

Go into the attic with a flashlight and look up toward the peak.

  • Rafters: you see parallel sloped boards climbing to a single board along the peak (the ridge board), and flat ceiling joists across the bottom. The middle of the attic is open, except perhaps for a few braces or collar ties.
  • Trusses: you see a row of identical triangles, often about 2 feet apart, each filled with smaller diagonal and vertical pieces called webs. Look closely at the joints and you will find flat metal plates with teeth pressed into the wood.

Many Central Arkansas homes have both. A truss main roof often sits beside a stick-framed porch, garage addition, dormer or vaulted room. If your home has a hip roof with gables over the garage, the framing may change from one section to the next. Our guide to hip roof vs gable roof explains those shapes.

How rafters work

A rafter roof is built in place by the framing crew. Each pair of rafters leans against a ridge board at the top and sits on the wall plate at the bottom. Because a pair of rafters pushes outward on the walls, the frame needs something holding the bottom ends together. Usually that is the ceiling joists, nailed to the rafters at the wall, or separate rafter ties higher up. Rafter sizes come from span tables in the building code, based on the lumber, the spacing and the load.

What rafters do well:

  • Open attic space for storage, ductwork or a future room.
  • Vaulted and cathedral ceilings, where the rafters themselves form the ceiling slope.
  • Odd shapes, additions and repairs, since the crew can cut each board to fit.

Where rafters can struggle: long spans need deep lumber, and an older rafter roof whose ties were removed or never installed can sag at the ridge or push the walls out. A sagging ridge line or a wavy roof surface is worth a closer look.

How trusses work

A truss is a ready-made triangle. The American Wood Council says metal-plate-connected wood trusses are "the predominant type of truss used in residential construction," are "typically fabricated from 2x4 or 2x6 dimension lumber," and are "designed using sophisticated software that accurately calculates the structural load conditions." The plates are pressed in with high-pressure equipment, and the trusses are inspected for plate placement before they ship.

The triangle shape spreads the load through every piece, so trusses can span the whole width of a house with smaller lumber and no interior bearing walls. The crew sets them on the walls, braces them and can often start sheathing the same day. According to STRUCTURE magazine's review of the residential code, truss design drawings must be provided to the building official and approved before installation, and trusses must be braced to keep them from rotating.

The trade-off is that a truss only works as designed. Every web and chord is part of the load path. The Structural Building Components Association puts it plainly: "NEVER cut any structural member of a truss!" It says any field change that cuts, drills or moves a truss member or connector plate needs approval from "the truss manufacturer or a licensed design professional," and that the International Residential Code (section R802.10.4) prohibits altering trusses.

Why this matters when you replace your roof

Shingles and metal panels do not care which frame is underneath. Both are covered by roof decking (also called sheathing), and the new roof is nailed into that decking. What the frame does decide is how well the deck stays flat and dry. Here is what we look for and what it means for you:

  • A straight roof line. A dip at the ridge or a wavy field can point to a sagging rafter, missing rafter ties, or a truss that was cut or damaged. New shingles will show every dip.
  • Altered trusses. A web cut out to fit an attic stairway, a duct or an HVAC unit is a red flag. That needs the truss maker or an engineer, not a roofer's guess.
  • Water stains on the framing. Dark stains running down a rafter or truss chord usually trace back to an old leak at a pipe boot, flashing or valley. The leak is fixed with the new roof; badly rotted framing needs a carpenter.
  • Ventilation openings. Ridge vents, roof vents, solar attic fans and skylights belong between framing members, not through them. See our post on ridge vents and attic ventilation in Arkansas.
  • Spacing and decking. Framing spacing decides how far each decking sheet spans. Soft spots between framing members usually mean the decking, not the frame, has failed.

What Patriot does on a roof replacement

Every Patriot Roofing and Restoration roof replacement includes a tear-off down to the decking, so the deck is checked before anything new goes on. The first 2 sheets of replacement decking are included, and more are $100 a sheet installed. Any rotted decking is photographed and priced in writing before it is replaced, as our post on rotted decking found at tear-off explains.

A free replacement inspection includes our 21-Point Roof Inspection Report with attic analysis and photos, so you see the framing we see. If we find a cracked rafter, a broken or cut truss member, or a sagging section, we photograph it and tell you before the job is priced, so it can be handled the right way first. Each new roof is backed by a Patriot Leak Free Guarantee of up to 15 years, depending on the package.

Frequently asked questions

Are trusses stronger than rafters?

Neither is stronger by definition. Both are sized to carry the loads the code requires. Trusses get their strength from the triangle and engineered plates; rafters get it from larger lumber and proper ties. A frame that has been cut, overloaded or soaked by leaks is the weak one, whichever kind it is.

Can I cut a truss to make attic storage or fit a new duct?

No, not on your own. The Structural Building Components Association says no truss member or plate may be cut, drilled or moved without approval from the truss manufacturer or a licensed design professional, and the residential code says the same. Call them first.

Does it cost more to reroof a house with rafters or trusses?

The framing type does not change the price of a new roof by itself. Roof size, pitch, shape, number of layers to tear off and decking repairs do. Our post on how many squares your roof is explains how size is figured.

What is a rafter tie?

A board that connects a pair of rafters low in the attic so they cannot push the walls apart. Ceiling joists often do this job when they are nailed to the rafters at the wall.

Can a sagging roof be fixed during a reroof?

Sometimes. If the sag comes from bad decking, new decking during the tear-off often takes care of it. If it comes from the framing, that needs a framing repair, and on trusses an engineer's or the truss maker's approved repair, before the new roof goes on.

Want us to look at your roof and attic?

If you are pricing a new roof, or a storm just came through, ask for a free storm or replacement inspection with our 21-Point Roof Inspection Report and attic analysis. For a leak or a repair, our repair diagnostic visit is $79.99, and Patriot Care Club members pay no service fee. Contact us to set it up.

Sources, checked November 18, 2026: American Wood Council, Trusses; Structural Building Components Association, Cutting Trusses; Brent Maxfield, S.E., STRUCTURE magazine, Code Requirements for Residential Roof Trusses.

Inspection

21-Point Roof Inspection

Your Roofing Specialist checks the roof and attic and gives you a 21-point report with photos of what we find.

$79.99

Roof Repair Diagnostic Visit

Includes the 21-Point Roof Inspection Report and attic analysis. Patriot Care Club members pay no service fee.

Book it now

Have No Fear, Patriot Is Here!

Call any time. Our phones are answered live 24/7.

Financing available, with approved credit

$0 down, 0% financing for 12 months, or payments of about $176 a month on $15,000 at 12.99% APR for 240 months. Soft credit check, approval in as little as 60 seconds.

Check My Options

Financing is with approved credit. Promotional rates and terms are not guaranteed and can change at any time. Payment example: $15,000 financed with $0 down at 12.99% APR for 240 months is 240 monthly payments of $175.63. 0% financing for 12 months is a promotional offer from the lender; the terms that apply after the promotional period are set by the lender. We work with more than one lending partner, and the rates and terms you are offered are set by the lender you are approved with, not by Patriot Roofing and Restoration. All rates and terms are presented to you in writing before you sign anything.

Instant Estimate